The following sections describe the safety and environmental items you must consider for an IBM Network Attached Storage Appliance.
Follow these rules to ensure general safety:
Remember: Metal objects are good electrical conductors.
|
Caution:Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the appliance covers, unless instructed otherwise in the installation and configuration procedures.
Observe the following rules when working on electrical equipment.
Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
Remember: Another person must be there to switch off the power, if necessary.
Remember: There must be a complete circuit to cause electrical shock. By observing the above rule, you may prevent a current from passing through your body.
Observe the special safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme care when measuring high voltages.
This practice ensures correct grounding of the units.
The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of non-IBM features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present:
The guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power cord disconnected.
Checklist:
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Notes:
When handling ESD-sensitive parts:
Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.
The safety notices in this section are provided in the following languages:
Be sure to read all safety notices before performing any of the instructions.
Statement 1
|
|
DANGER!
Electrical current from power, telephone and communication cables is
hazardous.
To avoid a shock hazard:
To Connect | To Disconnect |
---|---|
|
|
Statement 2
|
Caution:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system
has a module containing a lithium battery, replace it only with the same
module type made by the same manufacturer. The battery contains lithium
and can explode if not properly used, handled, or disposed of.
Do not:
Dispose of the battery as required by local ordinances or regulations.
Statement 3
|
Caution:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices, or
transmitters) are installed, note the following:
|
DANGER!
Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
Statement 4
|
|
|
|
>=18 kg (37 lbs) | >=32 kg (70.5 lbs) | >=55 kg (121.2 lbs) |
Caution:
Use safe practices when lifting.
|
|
Caution:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device.
The device also might have more than one power cord. To remove all
electrical current from the device, ensure that all power cords are
disconnected from the power source.
|
Statement 10
|
Caution:
Do not place any object weighing more than 82 kg (180 lb.) on top of
rack-mounted devices.
|
Importante:
Todas as instruções de cuidado e perigo da appliance Library começam com um número. Este número é utilizado para fazer referência cruzada de uma instrução de cuidado ou perigo no idioma inglês com as versões traduzidas das instruções de cuidado ou perigo encontradas nesta seção.
Por exemplo, se uma instrução de cuidado é iniciada com o número 1, as traduções para aquela instrução de cuidado aparecem nesta seção sob a instrução 1.
Certifique-se de ler todas as instruções de cuidado e perigo antes de executar qualquer operação.
Instrução 1
|
|
PERIGO
A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa.
Para evitar risco de choque:
Para Conectar: | Para Desconectar: |
---|---|
|
|
Instrução 2
|
CUIDADO:
Ao substituir a bateria de lítio, utilize apenas uma bateria IBM, Número de Peça 33F8354 ou uma bateria de tipo equivalente, recomendada pelo fabricante. Se o seu sistema possui um móídulo com uma bateria de lítio, substitua-o apenas pelo mesmo tipo de mídulo, do mesmo fabricante. A bateria contém lítio e pode explodir se não for utilizada, manuseada e descartada de maneira correta.
Não:
Para descartar a bateria, entre em contato com a área de atendimento a clientes IBM, pelo telefone (011) 889-8986, para obter informações sobre como enviar a bateria pelo correio para a IBM.
Instrução 3
|
PRECAUCIÓN:
Quando produtos a laser (unidades de CD-ROM, unidades de DVD, dispositivos de fibra ítica, transmissores, etc.) estiverem instalados, observe o seguinte:
|
PERIGO
Alguns produtos a laser contêm um diodo laser da Classe 3A ou Classe 3B embutido. Observe o seguinte:
Radiação de laser quando aberto. Não olhe diretamente para o raio a olho nu ou com instrumentos íticos, e evite exposição direta ao raio.
Instrução 4
|
|
|
|
>=18 kg (37 lbs) | >=32 kg (70,5 lbs) | >=55 kg (121,2 lbs) |
CUIDADO:
Ao levantar a máquina, faça-o com segurança.
Instrução 5
|
|
CUIDADO:
Os botões Liga/Desliga localizados no dispositivo e na fonte de
alimentação não desligam a corrente elétrica fornecida ao
dispositivo. O dispositivo também pode ter mais de um cabo de
alimentação. Para remover toda a corrente elétrica do
dispositivo, assegure que todos os cabos de alimentação estejam
desconectados da fonte de energia elétrica.
|
CUIDADO:
Instrução 10
|
CUIDADO:
|
Não coloque nenhum objeto com peso superior a 82 kg (180 lbs.)
sobre dispositivos montados em rack.
Important:
Toutes les consignes Attention et Danger indiquées dans la bibliothèque appliance sont précédées d'un numéro. Ce dernier permet de mettre en correspondance la consigne en anglais avec ses versions traduites dans la présente section.
Par exemple, si une consigne de type Attention est précédée du chiffre 1, ses traductions sont également précédées du chiffre 1 dans la présente section.
Prenez connaissance de toutes les consignes de type Attention et Danger avant de procéder aux opérations décrites par les instructions.
Notice n° 1
|
|
DANGER!
Le courant électrique passant dans les câbles de communication, ou les
cordons téléphoniques et d'alimentation peut être
dangereux.
Pour éviter tout risque de choc électrique:
Connexion | Déconnexion |
---|---|
|
|
|
Notice n° 2
ATTENTION:
Remplacez la pile au lithium usagée par une pile de référence identique exclusivement - voir la référence IBM - ou par une pile équivalente recommandée par le fabricant. Si votre système est doté d'un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant. La pile contient du lithium et présente donc un risque d'explosion en cas de mauvaise manipulation ou utilisation.
Pour la mise au rebut, reportez-vous à la réglementation en
vigueur.
|
Notice n° 3
ATTENTION:
Si des produits laser sont installés (tels que des unités de CD-ROM ou de DVD, des périphériques contenant des fibres optiques ou des émetteurs-récepteurs), prenez connaissance des informations suivantes:
|
DANGER!
Certains produits laser contiennent une diode laser de classe 3A ou 3B.
Prenez connaissance des informations suivantes:
Rayonnement laser lorsque le carter est ouvert. Évitez de regarder fixement le faisceau ou de l'observer à l'aide d'instruments optiques. Évitez une exposition directe au rayon.
Notice n° 4
|
|
|
|
>=18 kg | >=32 kg | >=55 kg |
ATTENTION:
Faites-vous aider pour soulever ce produit.
Notice n° 5
|
|
ATTENTION:
Le bouton de mise sous tension/hors tension de l'unité et
l'interrupteur d'alimentation du bloc d'alimentation ne coupent
pas l'arrivée de courant électrique à l'intérieur de la
machine. Il se peut que votre unité dispose de plusieurs cordons
d'alimentation. Pour isoler totalement l'unité du
réseau électrique, débranchez tous les cordons d'alimentation
des socles de prise de courant.
|
Notice n° 10
|
|
ATTENTION:
Ne posez pas d'objet dont le poids dépasse 82 kg sur les unités montées en armoire.
Wichtig:
Alle Sicherheitshinweise in dieser server-Bibliothek beginnen mit einer Nummer. Diese Nummer verweist auf einen englischen Sicherheitshinweis mit den übersetzten Versionen dieses Hinweises in diesem Abschnitt.
Wenn z. B. ein Sicherheitshinweis mit der Nummer 1 beginnt, so erscheint die übersetzung für diesen Sicherheitshinweis in diesem Abschnitt unter dem Hinweis 1.
Lesen Sie alle Sicherheitshinweise, bevor Sie eine Anweisung ausführen.
Hinweis 1
|
|
VORSICHT
Elektrische Spannungen von Netz-, Telefon- und Datenübertragungsleitungen sind gefährlich.
Aus Sicherheitsgründen:
Kabel anschlie&beta.en: | Kabel lösen: |
---|---|
|
|
Hinweis 2
|
ACHTUNG:
Eine verbrauchte Batterie nur durch eine Batterie mit der IBM Teilenummer 33F8354 oder durch eine vom Hersteller empfohlene Batterie ersetzen. Wenn Ihr System ein Modul mit einer Lithium-Batterie enthält, ersetzen Sie es immer mit dem selben Modultyp vom selben Hersteller. Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung explodieren.
Die Batterie nicht:
Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten.
Hinweis 3
|
ACHTUNG:
Wenn ein Laserprodukt (z. B. CD-ROM-Laufwerke, DVD-Laufwerke, Einheiten mit Glasfaserkabeln oder Transmitter) installiert ist, beachten Sie Folgendes:
|
VORSICHT
Manche CD-ROM-Laufwerke enthalten eine eingebaute Laserdiode der Klasse 3A oder 3B. Die nachfolgend aufgeführten Punkte beachten.
Laserstrahlung bei geöffneter Tür. Niemals direkt in den Laserstrahl sehen, nicht direkt mit optischen Instrumenten betrachten und den Strahlungsbereich meiden.
Hinweis 4
|
|
|
|
>=18 kg | >=32 kg | >=55 kg |
ACHTUNG:
Beim Anheben der Maschine die vorgeschriebenen Sicherheitsbestimmungen beachten.
Hinweis 5
|
|
ACHTUNG:
Mit dem Betriebsspannungsschalter an der Vorderseite des Gerätes und dem
Betriebsspannungsschalter am Netzteil wird die Stromversorgung für das
Gerät nicht unterbrochen. Das Gerät könnte auch mehr als ein
Netzkabel aufweisen. Um die gesamte Stromversorgung des Gerätes
auszuschalten, muß sichergestellt werden, daß alle Netzkabel aus den
Netzsteckdosen herausgezogen wurden.
|
Hinweis 10
|
ACHTUNG:
|
Keine Gegenstände, die mehr als 82 kg wiegen, auf Rack-Einheiten ablegen.
Importante:
Tutti gli avvisi di attenzione e di pericolo riportati nella pubblicazione appliance Library iniziano con un numero. Questo numero viene utilizzato per confrontare avvisi di attenzione o di pericolo in inglese con le versioni tradotte riportate in questa sezione.
Ad esempio, se un avviso di attenzione inizia con il numero 1, la relativa versione tradotta è presente in questa sezione con la stessa numerazione.
Prima di eseguire una qualsiasi istruzione, accertarsi di leggere tutti gli avvisi di attenzione e di pericolo.
Avviso 1
|
|
PERICOLO
La corrente elettrica circolante nei cavi di alimentazione, del telefono e di segnale è pericolosa.
Per evitare il pericolo di scosse elettriche:
Per collegare: | Per scollegare: |
---|---|
|
|
Avviso 2
|
ATTENZIONE:
Quando si sostituisce la batteria al litio, utilizzare solo una batteria IBM con numero parte 33F8354 o batterie dello stesso tipo o di tipo equivalente consigliate dal produttore. Se il sistema di cui si dispone è provvisto di un modulo contenente una batteria al litio, sostituire tale batteria solo con un tipo di modulo uguale a quello fornito dal produttore. La batteria contiene litio e può esplodere se utilizzata, maneggiata o smaltita impropriamente.
Evitare di:
Smaltire secondo la normativa in vigore (D.Lgs 22 del 5/2/9) e successive disposizioni nazionali e locali.
Avviso 3
|
ATTENZIONE:
Quando si installano prodotti laser come, ad esempio, le unità DVD, CD-ROM, a fibre ottiche o trasmettitori, prestare attenzione a quanto segue:
|
PERICOLO
Alcuni prodotti laser contengono all'interno un diodo laser di Classe 3A o Classe 3B. Prestare attenzione a quanto segue:
Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione diretta al fascio.
Avviso 4
|
|
|
|
>=18 kg | >=32 kg | >=55 kg |
ATTENZIONE:
Durante il sollevamento della macchina seguire delle norme di sicurezza.
Avviso 5
|
|
ATTENZIONE:
Il pulsante del controllo dell'alimentazione situato
sull'unità e l'interruttore di alimentazione posto
sull'alimentatore non disattiva la corrente elettrica fornita
all'unità. L'unità potrebbe disporre di più di un
cavo di alimentazione. Per disattivare la corrente elettrica
dall'unità, accertarsi che tutti i cavi di alimentazione siano
scollegati dalla sorgente di alimentazione.
|
Avviso 10
|
ATTENZIONE:
|
Non poggiare oggetti che pesano più di 82 kg sulla parte superiore delle
unità montate in rack.
Importante:
Todas las declaraciones de precauciín de esta Biblioteca del servidor empiezan con un número. Dicho número se emplea para establecer una referencia cruzada de una declaraciín de precauciín o peligro en inglés con las versiones traducidas que de dichas declaraciones pueden encontrarse en esta secciín.
Por ejemplo, si una declaraciín de peligro empieza con el número 1, las traducciones de esta declaraciín de precauciín aparecen en esta secciín bajo Declaraciín 1.
Lea atentamente todas las declaraciones de precauciín y peligro antes de llevar a cabo cualquier operaciín.
Declaración 1
|
|
PELIGRO
La corriente eléctrica de los cables telefínicos, de alimentaciín y de comunicaciones es perjudicial.
Para evitar una descarga eléctrica:
Para la conexin | Para la desconexiín |
---|---|
|
|
Declaración 2
|
PRECAUCIÓN:
Cuando desee sustituir la batería de litio, utilice únicamente el número de pieza 33F8354 de IBM o cualquier tipo de batería equivalente que recomiende el fabricante. Si el sistema tiene un mídulo que contiene una batería de litio, sustitúyalo únicamente por el mismo tipo de mídulo, que ha de estar creado por el mismo fabricante. La batería contiene litio y puede explotar si el usuario no la utiliza ni la maneja de forma adecuada o si no se desprende de la misma como corresponde.
No realice las acciones siguientes:
Despréndase de la batería siguiendo los requisitos que exija el reglamento o la legislaciín local.
Declaración 3
|
PRECAUCIÓN:
Cuando instale productos láser (como, por ejemplo, CD-ROM, unidades DVD, dispositivos de fibra íptica o transmisores), tenga en cuenta las advertencias siguientes:
|
PELIGRO
Algunos productos láser contienen un diodo de láser incorporado de Clase 3A o de Clase 3B. Tenga en cuenta la advertencia siguiente.
Cuando se abre, hay radiaciín láser. No mire fijamente el rayo ni lleve a cabo ningún examen directamente con instrumentos ípticos; evite la exposiciín directa al rayo.
Declaración 4
|
|
|
|
>=18 kg (37 libras) | >=32 kg (70,5 libras) | >=55 kg (121,2 libras) |
PRECAUCIÓN:
Tome medidas de seguridad al levantar el producto.
Declaración 5
|
|
PRECAUCIÓN:
El botín de control de alimentaciín del dispositivo y el interruptor
de alimentaciín de la fuente de alimentaciín no apagan la corriente
eléctrica suministrada al dispositivo. Es posible también que el
dispositivo tenga más de un cable de alimentaciín. Para eliminar
la corriente eléctrica del dispositivo, asegúrese de desconectar todos
los cables de alimentaciín de la fuente de alimentaciín.
|
Declaración 10
|
PRECAUCIÓN:
|
No coloque ningún objeto que pese más de 82 kg (180 libras) encima de los dispositivos montados en bastidor.
Federal Communications Commission (FCC) Class A Statement
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled Digital Apparatus, ICES-003 of Industry Canada.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouiller : Appareils Numériques, NMB-003 édictée par Industrie Canada.
Attention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Notice to Customers
This apparatus is approved under approval number NS/G/1234/J/100003 for indirect connection to public telecommunication systems in the United Kingdom.
This product has been tested and found to comply with the limits for Class
A Information Technology Equipment according to European Standard EN
55022. The limits for Class A equipment were derived for commercial and
industrial environments to provide reasonable protection against interference
with licensed communication equipment.
Warning:This is a Class A product. In a domestic
environment this product may cause radio interference in which case the user
may be required to take adequate measures.
|
Properly shielded and grounded cables and connectors must be used in order to reduce the potential for causing interference to radio and TV communications and to other electrical or electronic equipment. Such cables and connectors are available from IBM authorized dealers. IBM cannot accept responsibility for any interference caused by using other than recommended cables and connectors.
This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG) vom 30. August 1995 (bzw. der EMC EG Richlinie 89/336)
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen.
Verantwortlich für die Konformitätserklärung nach Paragraph 5 des
EMVG ist Scott Enke, Director, Worldwide Manufacturing Operations, PO Box
12195, 3039 Cornwallis, Research Triangle Park, NC U.S.A.
27709-2195.
Das Gerät erfüllt die Schutzanforderungen nach EN 50082-1 und EN 55022 Klasse A. |
EN 55022 Klasse A Geräte müssen mit folgendem Warnhinweis versehen
werden:
"Warnung: Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im
Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber
verlangt werden, angemessene Maßnahmen durchzuführen und dafür
aufzukommen."
EN 50082-1 Hinweis:
"Wird dieses Gerät in einer industriellen Umgebung betrieben (wie in EN 50082-2
festgelegt), dann kann es dabei eventuell gestört werden. In solch einem Fall ist
der Abstand bzw. die Abschirmung zu der industriellen Störquelle zu
vergrößern."
Anmerkung:
Um die Einhaltung des EMVG sicherzustellen, sind die Geräte, wie in den IBM
Handbüchern angegeben, zu installieren und zu betreiben.